CAREERS

Male Candidate is Preferable

Should be able to handle a Team of 5 To 10 Employees

Age : 30 To 35 Years

Exp : 8 To 12 Years in the field of Power Electronics

Required Skill : Lead the design activity of various high power Battery Chargers, DC-DC Converters, Rectifiers, SMPS, OP-AMP and Motor Drivers. Magnetic design of converter
components is mandatory.
Thorough understanding in Analog circuit design, Thermal modelling of power electronic devices, heat sink design/calculation, EMI and EMC.
Experience in Schematic design, Simulation/analysis, PCB layout guidance/verification, Prototype testing are preferable
Developing Electronics hardware right from paper to prototype. Alternate design analysis, POC evaluations and documenting.
Detail design document with EMI/EMC consideration, Component Tolerance, de-rating calculations
Validating design for high reliability and robustness & Performing Functional and Compliance Testing
Knowledge in using Multimeter, Oscilloscope, Network analyzer and power supplies. Full bridge topologies, understanding of MOSFET

*Software development using LabVIEW, NI Labview RT & NI Labview FPGA modules.
*BE (EEE or ECE) with greater than 3 years of experience…..
*Basic knowledge of signal processing using NI LabVIEW functions.
*Good experience in NI’s Data Acquisition hardware (NI DAQ), CRIO, NI SBRIO-9606 hardware, NI GPIC-9683 hardware, Signal condition, Sensors, instruments programming and remote control, Software debugging, Integration and testing.
*Well versed in RS-232, RS 485, TCP/IP Modbus and CAN communication protocols.
*Hands-on experience with test and measurement instrumentation such as oscilloscopes and analyzers.
*Basic knowledge of industrial motor control and servo motor, switching contactors and relays, pneumatic system, hydraulic system, temperature control and measurement, pressure control and measurement, vibration test.
*Basic knowledge of test system control panel design, Noise isolation, Grounding techniques, Design for Safety and Ergonomics requirements.
*Certification on “Embedded Control and Monitoring using Labview” is added advantage.
*NI LabVIEW certifications – Certified LabVIEW Associate Developer(CLAD) or Certified LabVIEW Developer(CLD) or Certified LabVIEW Architect(CLA) are added advantage

*NI = National Instruments
*RT = Real Time Programming

*Lead the design activity of various high power Battery Chargers, DC-DC Converters, Rectifiers, SMPS, OP-AMP and Motor Drivers. Magnetic design of converter components is mandatory.
* Thorough understanding in Analog circuit design, Thermal modelling of power electronic devices, heat sink design/calculation, EMI and EMC.
* Experience in Schematic design, Simulation/analysis, PCB layout guidance/verification, Prototype testing are preferable.
* Developing Electronics hardware right from paper to prototype. Alternate design analysis, POC evaluations and documenting.
* Detail design document with EMI/EMC consideration, Component Tolerance, de-rating calculations.
* Validating design for high reliability and robustness & Performing Functional and Compliance Testing.
* Knowledge in using Multimeter, Oscilloscope, Network analyzer and power supplies. Full bridge topologies, understanding of MOSFET.

*Attractive Salary, Immediate joiners are preferable

*Basic knowledge of Online/Offline Tendering (government project), Online/Offline bidding, Cost estimation, Quotation in any Manufacturing Industry.

*Good Communication skill

*SAP experience and ISO knowledge is added advantage.

*Gender: Male/Female can apply

-Hands on experience in Project Planning(PPC), Stakeholder management, Risk management, Material Management is mandatory.
-Exposure in team handling.
-Analyzing of mechanical manufacturing drawings, electrical harness drawings, circuits and implementing the same.
-Knowledge in Electrical CADD is a plus.
-4 to 5 years of experience in DG Set of Power Units Manufacturing is an advantage.

-Bachelor’s degree in electrical engineering the qualification of BE(EEE) with MBA is preferable.

-PMP(Project Management Provisional ) certification is preferred.

* Good Knowledge in SAP business1 moduleMinimum 5 years experience in SAP B1, Microsoft SQL, Crystal Report is mandatory
Experience in Crystal report generation is mandatory
Experience in Minimum SQL Query Generation is mandatory
SAP B1 Addon certification is an added advantage
SAP B1 Functional support
Good Knowledge in SAP business1 module
Hands on exp. In functional report analysis
Able to understand the dept. process requirements
Immediate joineers are most welcome
Male candidates only
* Hands on exp. In functional report analysis
* Able to understand the dept. process requirments

INVENTORY MANAGEMENT
LOGISTICS MANAGEMENT
FULFILLING STORES SOP REQUIEMENTS
MANAGING A TEAM CONSISTING OF 20+ MEMBERS
SUBMISSION OF MIS REPORTS
COMPUTER OPERATING – MS OFFICE & ERP / SAP
EFFECTIVE COMMUNICATION AND REPORTING
MAN MANAGEMENT WITH LEADERSHIP QUALITY

* Must know to Commissioning, Servicing, Trouble Shooting and Testing of DG set
* Knowledge in Engine Overhauling,motor Repair related works.
* Should know basic concept of Engine related problems.

* Able to Service the electrical Product and also Installation related works.
* Commissioning activities of PCA & SFPCA(Pre-Conditioned Air & Sub Freezing Pre-Conditioned Air) units.
* Should have good communication and customer handling skills.

* Knowledge in drafting and designing of products.
* Knowledge in drafting & modeling software like Auto cad, Solid works.
* Sheet Metal product experience added an advantage.
* Exposure in Auto cad Inventor, Ansys, etc.,
* Knowledge container/enclosure design & its selection calculations
* Knowledge in geometric tolerance & dimension

* Must have hold relevant certification or relevant experience in welding field.
* Basic knowledge of metals and related process.

* Require Senior Engineer – Service for our Customer Relation Management Department
* He should be Handling / Visiting customers for understanding
* Studying new projects, Guiding Service Engineers, Attending major services
* Commissioning, Conducting training to customers etc.
* Fluency in English & Hindi
* Spoken Hindi is preferable
* MBA could be additional advantage OR with special courses like CADD, PLC etc.,

* Hands on experience in PLC Programming.
* Must be experienced in Scada – Siemen Like Applications.
* Must be experienced in communication protocol like RS232, RS485, Modbus TCP/IP, Ethernet.
* Implementation of electrical and control systems consisting of PLC, HMI, motors, sensors etc.
* Implementation/ testing/ configuration of electrical circuits, control circuits, field/IO circuits etc.
* Must be experienced in database connection like SQL sever.
* Must have experience in Visual Basic scripting.
* Having exposure to handling the team and splitting the work among the team is a plus
* Must have team management skills

*Must have basic structural design knowledge
*Must have exposure to Sheet metal design, heavy structure design such as pallets
*Must have experience in 3D & 2D drafting
*Must have exposure in GD&T (Geometric Dimensions & Tolerance)
*Must have knowledge & Experience in Autodesk inventor, Autocad softwares

* Hands on Experience on Servicing the Electrical Product and also Installation and Commissioning activities.
* Ready to travel all over India through out the year.
* Should be have good communication over English and Hindi.

* Looking for Preferably Male Candidate
* Languages Known:- Android Studio, Java, Kotlin, PHP, MySQL, Python.
* Operating System:- Linux OS for Android OS compilation and Windows for app development.
* Experience working with remote data via REST and JSON
* Libraries: Realm database, Retrofit Library & Dagger (dependency injection)
* Communication protocols: UDP, TCP/IP, HTTP, RS485
* Should handle hardware devices through Android OS, Raspberry pi & IoT devices.
* Should demonstrate one project developed in Android during the Interview.